LM35 TEMPERATURE SENSOR INTERFACING WITH 8051 PDF

The project is built to demonstrate working of LM35 temperature sensor interfaced with through ADC The LM35 series are precision. LM35 is a 3 pin temperature sensor, which is pretty accurate in detecting Interfacing LCD in Temperature Indicator using and LM SENSOR INTERFACING: Temperature Sensor (LM35) INTERFACING with PIC18F Aditi Nandi-vtu, Leya Gopal,-vtu, Degala Vani-vtu

Author: Goltizshura Gokinos
Country: Guinea
Language: English (Spanish)
Genre: Politics
Published (Last): 10 September 2016
Pages: 404
PDF File Size: 8.55 Mb
ePub File Size: 2.95 Mb
ISBN: 253-7-20267-279-5
Downloads: 31755
Price: Free* [*Free Regsitration Required]
Uploader: JoJoshura

The problem should be with your hardware, check the contrast pin of the LCD. The LM35 would give a total output voltage 1v since every degree has a value of 10mv and so a range of 0 to 1V. The command is copied to port 0 of microcontroller. Is it possible to use the code for Proteus Simulation?

It outputs 10mV for each degree of Celsius temperature. Quote and Order boards in minutes on https: After a specified time delay, next cycle starts.

This process is repeated after specified interval.

SENSOR INTERFACING with | Guduru Vijayalakshmi –

Any good programmer has the capability to read the configuration information from the hex file and transfer it to the MCU. Please help us ASAP as it is required for our academic project.

Voltage the answer will be of a 2. They are data register and command register. The LM35 is a temperature sensor whose output voltage is linearly proportional to Celsius temperature.

Get Our Weekly Newsletter! These double checks enables to remove errors when you do it on a hardware. LM35 looks like a transistor it will give you temperature in Celsius in terms of millivolt.

Command register is 8015 to send commands such as clear display, cursor at home etc. Converting Integer to Characters in Ansi C. The result is a sequence of digital values that have converted a continuous-time and continuous-amplitude analog signal to a discrete-time and discrete-amplitude digital signal.

Keep up the good work! An example of the use of an adjusted reference voltage is to accommodate a reduced span—or dynamic voltage range of the analog input voltage. Mainly the Lm53 has 3 pins, which are: Remember me on this computer. Interfacing means-A hardware interface is used to connect two or more electronic devices together. LM35 is a 3 pin device as show above.

The code is split into small meaningful chunks and explained below. Programs will not run without proper configuration byte programming. INTR becomes low at the end of conversion. Here how it looks:.

Skip to main content. Are you sure the code is uploaded correctly?

Temperature sensor(lm35) interfacing with 8051

If yes then try a basic blink program on your hardware and check if that is working properly. What is the problem? Awesome, keep it up.

RS is made high for command write.

ADC interfacing with (LM35 Interfacing) | EmbeTronicX

RS is made low for command write. It can be used with single power supplies, or with dual supplies. Then this temperature is converted into ascii form which is suitable for displaying. If the analog input voltage were to range from 0. From ADC these digital signals are sent to Microcontroller which displays the temperature of that environment.

The extra part required for this project like LCD and the LM35 temperature sensor are installed in the expansion board. This means that when the temperature is 0 oC then the output voltage is 0V.

This has been achieved in the design of the IC as shown in Figure. The main objective of this paper is to the complete overview of sensor interfacing i.

After this part the microcontroller will need certain routines so that it can convert this 8-bit data ADDH register for the ADC of the micro to a specific Temperature varying from 0oC to oC.

It is defined as exchange of Input or output data between sensor and PIC microcontroller or other devices. The conversion involves quantization of the input, so it necessarily introduces a small amount of error. This value of temperature is then display on the LCD 20 by om35. It can be used with single power supplies, or with plus and minus supplies. Thanks and more power.

Major problems arises due to improper soldering, solder jumps and loose joints. Interfacing Keypad with As explained the microcontroller will get the analogue voltage, which is generated, from the LM35 plus the gain block.

The full 8 bits of resolution are therefore applied over this reduced analog input voltage range. Finally the complete working process, its characteristics, applications will be discussed in this paper.